【スプリングピン ストレート形 一般用】 JIS 2808
すきまＣは、スプリングピンを適用する穴に挿入したとき、辺が接触しないような寸法でなければならない。（但し、両端部を除く）
※呼び径１２・１３の対応サイズは、『ばね用鋼』のみの取扱いになります。
※ステンレスの呼び径８mmは、長さ『１６』『４０』のみになります。
|
材質：SUS４２０Ｊ２ |
材質：ばね用鋼 |
|
表面：光沢仕上げ |
表面：ﾃﾝﾊﾟｰｶﾗｰ |
|
硬度：HRC４２〜４８ |
硬度：HRC４５〜５３ |
単位mm
|
呼び径 |
1 |
1.2 |
1.4 |
1.5 |
1.6 |
2 |
2.5 |
3 |
3.5 |
4 |
4.5 |
5 |
6 |
7 |
8 |
10 |
12 |
13 |
|
|
外径 Ｄ |
最大 |
1.2 |
1.4 |
1.6 |
1.7 |
1.8 |
2.25 |
2.75 |
3.25 |
3.9 |
4.4 |
4.9 |
5.4 |
6.4 |
7.6 |
8.6 |
10.6 |
12.6 |
13.7 |
|
最小 |
1.1 |
1.3 |
1.5 |
1.6 |
1.7 |
2.15 |
2.65 |
3.15 |
3.7 |
4.2 |
4.7 |
5.2 |
6.2 |
7.3 |
8.3 |
10.3 |
12.3 |
13.4 |
|
|
t |
0.2 |
0.25 |
0.28 |
0.3 |
0.3 |
0.4 |
0.5 |
0.6 |
0.7 |
0.8 |
0.9 |
1 |
1.2 |
1.4 |
1.6 |
2 |
2 |
2.5 |
|
|
二重せん 断荷重 |
kN |
0.69 |
1.02 |
1.35 |
1.55 |
1.68 |
2.76 |
4.31 |
6.20 |
8.45 |
10.80 |
13.96 |
17.25 |
24.83 |
33.83 |
44.13 |
68.94 |
86.22 |
112.78 |
|
適用する穴 |
径 |
1 |
1.2 |
1.4 |
1.5 |
1.6 |
2 |
2.5 |
3 |
3.5 |
4 |
4.5 |
5 |
6 |
7 |
8 |
10 |
12 |
13 |
|
許 容 差 |
+0.08 0 |
+0.09 0 |
+0.12 0 |
+0.15 0 |
+0.2 0 |
||||||||||||||
|
長さ Ｌ |
許 容 差 |
呼 び 径 |
|||||||||||||||||
|
1 |
1.2 |
1.4 |
1.5 |
1.6 |
2 |
2.5 |
3 |
3.5 |
4 |
4.5 |
5 |
6 |
7 |
8 |
10 |
12 |
13 |
||
|
４ |
+0.5 0
|
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
|
|
|
|
|
５ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
|
|
|
|
|
６ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
|
|
|
|
７ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
|
|
|
８ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
|
９ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
|
１０ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
１１ |
+1 0
|
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
１２ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
１３ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
１４ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
１５ |
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
|
|
|
|
|
１６ |
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
|
|
|
|
|
１７ |
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
|
|
|
|
|
１８ |
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
|
|
|
|
１９ |
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
|
|
|
|
２０ |
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
|
|
|
２１ |
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２２ |
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２４ |
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２５ |
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２６ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２７ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２８ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
２９ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
３０ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
３２ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
３５ |
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
３６ |
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
４０ |
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
４５ |
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
５０ |
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
|
○ |
○ |
○ |
○ |
|
|
５５ |
|
|
|
|
|
|
|
|
|
|
|
|
○ |
|
○ |
○ |
○ |
○ |
|
|
５６ |
+1.5 0
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
|
○ |
○ |
○ |
○ |
|
６０ |
|
|
|
|
|
|
|
|
|
|
|
|
○ |
|
○ |
○ |
○ |
○ |
|
|
６３ |
|
|
|
|
|
|
|
|
|
|
|
|
○ |
|
○ |
○ |
○ |
○ |
|
|
７０ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
|
|
７５ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
|
|
８０ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
○ |
|
|
８５ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
|
|
９０ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
|
|
９５ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
|
|
１００ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
○ |
○ |
○ |
|
備考 ： Dの最大寸法はピンの円周上における最大値とし、Dの最小寸法は1/3（D1+D2+D3）とする。
注意 ： この製品は、需給状況により加工実績がないサイズがありますのでお問合せください。
|
Copyright (C) 2008 koueifastener. All rights reserved.
|